I have a 08 outlander 800. So i ruin my spark plug connector today. Does anyone have a replacement number for it? I’ve been searching but not sure if i’m getting the right part. I need the connector that screws in to the wire? Just want to make sure that part #420265248 (connector). Looking at the picture it looks like just the cap that covers the connector.
Spark Plug Connector???
I have a 08 outlander 800. So i ruin my spark plug connector today. Does anyone have a replacement number for it? I’ve been searching but not sure if i’m getting the right part. I need the connector that screws in to the wire? Just want to make sure that part #420265248 (connector). Looking at the picture it looks like just the cap that covers the connector.
HMF slip on
Iam looking at getting an HMF performance slip on for my 07 500xt. Am I able to run this pipe stock or will I have to get a programmer. Don’t want to tear anything up.
Windrock Spring Jam 2015 Videos!!
Had a blast last weekend at the Spring jam up at Windrock. Was an awesome time with just me, my son and Wife coming along. Turned out to be a great family getaway trip!
Here are some video from the weekend! Hope yall enjoy!!
First up is a small video I let Colton film most of it. You can tell it was him in the end!!
https://www.youtube.com/watch?v=GEt8fIQkFkM
Next up is Mandy and Colton blasting through a huge mudhole! I think I taught her well!
https://www.youtube.com/watch?v=LRJAnr6rn4U
Rest are from the events!! I placed 4th in the new Obstacle coarse, and due to new classing in the mud drag, didn’t win ( can’t beat any can am 1000s!! )
https://www.youtube.com/watch?v=ehxPpx6VWjE
https://www.youtube.com/watch?v=3LJ2WSmJhSE
https://www.youtube.com/watch?v=A2DTCJwA39I
https://www.youtube.com/watch?v=42WwhkMc8w0
Do you have a junk stock XP 1000 muffler…If so
Do you have a junk XP4 XP 1000 muffler with good ends. I am working on a project and need the ends. If you could hacksaw them off as close to the muffler as possible, at the welds. Header side and exit side with spark arrestor.
PM me and let me know how much shipped to 93446
Do you have a junk stock XP 1000 muffler…If so
Do you have a junk XP4 XP 1000 muffler with good ends. I am working on a project and need the ends. If you could hacksaw them off as close to the muffler as possible, at the welds. Header side and exit side with spark arrestor.
PM me and let me know how much shipped to 93446
Best tires for TRX 90
I just spent $700 on a 2002 TRX 90 for the grand-kids. It runs good, but one of the front tires leaks and has a plug in the side wall. One of the rear tires is also leaking, so I’m thinking I should just replace them all.
It looks like I can get a full set of either the Maxxis M953/M954 or Carlisle Trail Wolfs in the stock sizes for a little over $200. Any recommendation?
Best tires for TRX 90
I just spent $700 on a 2002 TRX 90 for the grand-kids. It runs good, but one of the front tires leaks and has a plug in the side wall. One of the rear tires is also leaking, so I’m thinking I should just replace them all.
It looks like I can get a full set of either the Maxxis M953/M954 or Carlisle Trail Wolfs in the stock sizes for a little over $200. Any recommendation?
Genoa,Ne
Anyone going to Genoa Sunday when the track opens? I’ll be heading there thought it would be cool to maybe meet some people from the forums.
98 Sportsman 500 starting issue
Recently I was suckered into replacing the motor on this 500 due to the fact the previous one burned up because of the oils screen was plugged up. Anyway my buddy bought a used motor and the seller installed a new can once the motor was out of the quad. So the motor arrived at my home and like a good buddy I double checked the can installation. All appeared fine with the exception the timing was way off.
I also checked the valves and set them to .006 (lobes down dots up)the engine will start and it sounds good when I can get it to roll over that is. Using the pull rope it is very difficult to pull and the starter drags as in it doesn’t seem to have the torque required to turn this motor. With the clutch cover off at times its very hard for me to rotate the engine by hand.
I am assuming that the decompression valve may be the culprit however I don’t see anything wrong with it. I pulled it apart and it all appears fine. The ball bearing is in place and so is the mechanism.
Keep in mind that it sounds great when it fires up but I am at a loss as to what to look at next
