I recently bought a 2009 Polaris Sportsman 500. Only downfall was the lens on the speedo was half broken out. I thought no biggie, I’ll just replace the lens. Then I realized you have to replace to whole thing, or so I thought. Went online looking for solutions. After a lot of research, I found a product called Weld On 4. It’s used to "weld" plastics together. Not just glue, but chemically bond, and seal the joint. Well tonight I successfully fixed the lens on my speedo, for all of about $25. Bought a piece of Acrylic plexi-glass ($10), and the Weld On 4 was $14 shipped, with applicator for the job. Just thought you guys might be interested in saving a ton of cash! Good luck!
Fixing broke Len on speedo’s
I recently bought a 2009 Polaris Sportsman 500. Only downfall was the lens on the speedo was half broken out. I thought no biggie, I’ll just replace the lens. Then I realized you have to replace to whole thing, or so I thought. Went online looking for solutions. After a lot of research, I found a product called Weld On 4. It’s used to "weld" plastics together. Not just glue, but chemically bond, and seal the joint. Well tonight I successfully fixed the lens on my speedo, for all of about $25. Bought a piece of Acrylic plexi-glass ($10), and the Weld On 4 was $14 shipped, with applicator for the job. Just thought you guys might be interested in saving a ton of cash! Good luck!
Fixing broke Len on speedo’s
I recently bought a 2009 Polaris Sportsman 500. Only downfall was the lens on the speedo was half broken out. I thought no biggie, I’ll just replace the lens. Then I realized you have to replace to whole thing, or so I thought. Went online looking for solutions. After a lot of research, I found a product called Weld On 4. It’s used to "weld" plastics together. Not just glue, but chemically bond, and seal the joint. Well tonight I successfully fixed the lens on my speedo, for all of about $25. Bought a piece of Acrylic plexi-glass ($10), and the Weld On 4 was $14 shipped, with applicator for the job. Just thought you guys might be interested in saving a ton of cash! Good luck!
Trx 90 no spark?
Just picked up a 2000 trx 90 and has no spark. There is a yellow wiring on the left of the machine and its not connected to anything. It has power going to it when i pull start it. Any idea what it might go to? Dont see anywhere to connect it to?? Thanks
Winch out Backwards?
I have a rzr s 800 with a front mounted 4,500 winch. If I ever need to winch in reverse, does it work to run the winch cable backwards under the rzr to winch backwards?
hornblasters
i have a complete set-up of hornblasters shocker-2 setup, looking to trade for a good audio system for my 800s. might consider other stuff for my rzr also, feedback reference on ebay as buggzy99.
check out hornblasters.com or youtube for videos
Clutch problem, I thought I had it
My clutch plates were seized so I took it apart and freed the discs/plates and everything measured good. Waited a week for the gasket and went to put it back together today. Fired it up and put it in gear, it jumped a bit in the direction I shifted into like everything was good. Gave it throttle and nothing. I must not have aligned something properly putting the case back on or something worse. Any thoughts on what I screwed up? BTW, this is a 1999 300FW
Clutch problem, I thought I had it
My clutch plates were seized so I took it apart and freed the discs/plates and everything measured good. Waited a week for the gasket and went to put it back together today. Fired it up and put it in gear, it jumped a bit in the direction I shifted into like everything was good. Gave it throttle and nothing. I must not have aligned something properly putting the case back on or something worse. Any thoughts on what I screwed up? BTW, this is a 1999 300FW
My 1000 xp picture thread :)
I couldn’t be outdone by XP 1000..LOL, here’s my picture thread
trx300 electrical fault
have owned a trx300 for many years that I use for pig hunting and gold prospecting in aussie outback but have developed electrical issue. Sometimes I must let the bike idle for a while before touching the throttle or it cuts out, sometimes turning the handle bars while reversing out of the shed, and sometimes wont fire at all. I have replaced both cdi boxes checked wiring and cant find the fault. All of a sudden it will come good. Any ideas maybe oil temp sender. When bike is hot no problem. thanks wayne
