I recently lost my hqndle bar cover and bought a new one..however my old one was cut to fit around my windsheild. Does anyone have a picture of there already cut? I can widdle away at mine but it would be nice to see how much i have to take off. Thanks

I recently lost my hqndle bar cover and bought a new one..however my old one was cut to fit around my windsheild. Does anyone have a picture of there already cut? I can widdle away at mine but it would be nice to see how much i have to take off. Thanks

I have an 01 Polaris Trailblazer 250. I am missing the locknut for the flywheel. I was told it was a 16×1.5. I picked one up from a hardware store and it doesnt fit. 16 is the right size but im not sure about the thread count. The 16×1.5 seems too coarse. Can anyone help me with the correct size

Hello,

I work in a garage. We usually service and repairs motorcycles. People around here owns many atvs, so upgrading our workshop to repair it would be an advantage.We are finding a lift table to station atv since what we use for motorcycles are small.

Has anyone bought a lift table for your atv, because we heard people having issues about the width and girth on the table. As now we found this scissor lift table but it is for heavy duty applications.

Hello,

I work in a garage. We usually service and repairs motorcycles. People around here owns many atvs, so upgrading our workshop to repair it would be an advantage.We are finding a lift table to station atv since what we use for motorcycles are small.

Has anyone bought a lift table for your atv, because we heard people having issues about the width and girth on the table. As now we found this scissor lift table but it is for heavy duty applications.

Seems the mood here on the forum is a little antagonistic lately.

How about giving a caption for the genius in this photo?

"Martha, this view is absolutely breathtaking…maybe it’s the quad on my chest…."

Smoky Joe is getting the cylinder head honed a little due to some scoring. The machine shop figured about 0.25 mm oversized piston, which I think I’ve located, but I haven’t been able to locate rings to go along with it…

Smokey Joe is a ’94 200cc TRX D type II.

The stock cylinder ID is 65.000-65.010mm
The stock piston OD is 64.962-64.982mm

So I have checked the usual outlets–ebay, hondaparts, bike bandit, to no avail.

Anyone have any leads?

Hello all,

I had a 2013 Outlander 1000 XT, with a Power Commander V and Yoshimura slip-on. I had it dyno’d and a custom fuel map made.

I kept the Power Commander and Yoshimura, and put them on my 2016 Outlander XMR 1000R.

Will the same map work, without spending another $400 to have another map made?

If not – if anyone has the same machine and pipe, with a dyno tuned map, I’ll buy the map from you, to help offset a small chunk of the cost you paid.

Thank you.

Sent from my LG-H900 using Tapatalk

Hello all,

I had a 2013 Outlander 1000 XT, with a Power Commander V and Yoshimura slip-on. I had it dyno’d and a custom fuel map made.

I kept the Power Commander and Yoshimura, and put them on my 2016 Outlander XMR 1000R.

Will the same map work, without spending another $400 to have another map made?

If not – if anyone has the same machine and pipe, with a dyno tuned map, I’ll buy the map from you, to help offset a small chunk of the cost you paid.

Thank you.

Sent from my LG-H900 using Tapatalk

I have a 96 300 4×4 and it wasn’t firing when I first got it so I had the plug in and out while trying to find out what was wrong. There was no oil on the plug until i got it to fire. Now it’s soaked and not starting. It turns over and then tries to start then turns over then tries to start. You could set your watch by when it’s gonna try to start. It also backfires through the carb. So I checked and it’s in time. The chain tensioner is all the way extended so I know I need to put a new chain on. Question is would this cause my symptoms or could it be rings. Don’t understand why the plug only got oily when I got it firing.