Category Archives: General RZR Discussion

RPM problem XP 900

At 1550 miles I had warranty replace top end on rzr due to burning oil, while at it I had them put in JaggedX cams and valve springs. Got rzr back and ran great, 400 miles later at dumont it stopped reving pass 7500 rpms. Pulled clutch cover and realized rollers were flat and wore grooves in sliders on secondary, also primary was a lil sloppy. Replaced with brand new OEM clutches and put in SLP clutch kit. Fine tuned weights and Runs good for first good run till drive train gets hot, then limits my rpms to 7900 uphill, downhill, flats. But pulls 8400 till everything gets hot.. I’m stumped!! Any suggestions?

upholster seats

Hey guys, so I bought some seats when I got my new 2015 xp4 1000 voodoo blue…. I since have done custom cage and alot of other stuff, well since then my color scheme has totally changed. I’m wondering if there’s anyway to get my seats re upholstered so I don’t have to buy new seats….any help would be appreciated! Attachment 131789

Attached Thumbnails

Click image for larger version

Name:	uploadfromtaptalk1429063936794.jpg
Views:	N/A
Size:	172.1 KB
ID:	131789
 

Polaris parts

When i bought my RZR i told them for me to buy the rzr 1000. I wanted all the accessories at 10% over cost after purchase. Well now their trying say that the best they can do is 10% off and COST isnt much below that. So does anyone know what dealers pay for the front plastic that holds the healights in and the rear storage bins? Im hot about the situation because a deal was a deal and i cant see how a business can make any money with so low of profit margins. I think they are screwing me 😈

Sunk my RZR 800…what now?

Afternoon everyone,

Checking to see if you might have suggestions on what to do next? On a recent camping trip to northern Arkansas, we were riding down a shallow….well, at least part of it was….creek. It was about 10"-12" deep until the front end of my RZR went into a hole. Before I could get turned around, the 40 something degree water came up to my chest and the only thing sticking out of the water was about one foot of the top of the RZR.

Needless to say, it was completely flooded. I got pulled out and towed back to our camp. The air cleaner had about 1/2 gallon of water in it and the oil was milky, to say the least. Loaded it up and drove it home the next day.

Here’s what I’ve done so far: Drained the oil and removed/discarded the filter; discarded the air filter; removed the belt housing and drained water; spray all connections with WD-40; disconnected the battery…..Replaced oil and filter (5) times till oil no longer shows milky color.

Now, RZR starts and idles for approximately one minute before stopping. Restart and goes for another minute. When I give it the gas, it dies immediately. Suggestions??

Thanks in advance!

How much slop

The other day while riding started to hear a strange noise almost like a bad wheel bearing. Jacked it up and all wheels and bushings felt tight. Noticed rear of drive shaft had decent play. Should they be tight on splines. Replaced u joint but not yoke. Drive it down my street and noise was still there but not as bad. Checked it and yoke still had play. So I orded new rear yoke. Are they suppose to be tight just making sure there isn’t another issue. You would think it would be tight I have 1400 miles on it.

How much slop

The other day while riding started to hear a strange noise almost like a bad wheel bearing. Jacked it up and all wheels and bushings felt tight. Noticed rear of drive shaft had decent play. Should they be tight on splines. Replaced u joint but not yoke. Drive it down my street and noise was still there but not as bad. Checked it and yoke still had play. So I orded new rear yoke. Are they suppose to be tight just making sure there isn’t another issue. You would think it would be tight I have 1400 miles on it.