Category Archives: General RZR Discussion

trying to decide please help!!!

Been looking at 1K but also looked at 99 pg thread with all the problems.

I’ve been a loyal polaris owner and have a 850 touring. My questions is are most of the problems with the earlier models taken care of or are there still a lot of problems even the the 15’s. I’ve read the whole 99 pages and have seen everything from glove boxes not closing to trans leaking to noises in front end to shocks bending and all kinds of stuff. Have these issues been taken care of or has polaris ignored them with the later release of the new models?

Any info would be great!!!

Feeling the water

Well guys, some things have changed in my personal and I may have to sell my custom 2012 RZR 900 4 seater. I am feeling the water to see what it may be worth to someone who appreciates what I started.

I WILL NOT PART IT OUT, SO PLEASE DONT ASK.

What I have, and this description will not do it justice.
2012 RZR 900 4 seater. Only 20 hours on car.
Full custom built DOM .120 wall cage with front bumper, roof mounted light bar, tied to rear with spare tire mount. Spare tire panel is on heims, raises on gas strut for bed access
All custom fab aluminum panels, sides are 3/4 high, front to back, rear is all aluminum with light box, side panels, rear panel, front end is all aluminum one of a kind custom.
Dash is all aluminum custom with turbo gage pod.
Aluminum roof, with aluminum boxed switch panel that runs along top of cage, inside. Hex Zues fasteners through out.
5 Hella lights in roof mounted light bar and 2 more in custom front bumper.
Custom cage is powder coated and all aluminum is raw, sand finish.
I designed this car to resemble an old school race car, I wanted to look different

The stereo consists of 5 channel JL audio amp, 500 wats of real power, JL audio
10W3 dual voice coil sub, 6" Boston Acustic Pro separates with crossovers.
Amp and crossovers are mounted under the dash in a custom built heavy duty
rack. Sub and speakers mounted in SSV Works enclosures. Car is wired for rear speakers as well.
Custom heavy duty battery box mounted under the rear seat with a Kinetik pro sound competition battery, and smart battery isolator. Battery weighs 65 pounds and will power the sound system for hours and hours.
Miles and miles of custom wiring harnesses, wrapped in conduit, and double warped in heavy duty electrical tape. Car is wired for accessories galore. Extra fuse box and relay bank wired in.
PRP Baja competition seats, extra wide, heated in the front, PRP bench in the
rear, all with embroidered logos in the head rests. 5 point harnesses front and rear. Very, very comfortable.
Sommers Brothers Racing 300M rear axles with 570 CV’S just serviced by S.B. Plus 2 stock spares.
Holtz Racing billet engine and transmission mounts.

Here is where it gets good.
The engine is a K&T 975 big block, built by KingR here on the forum, 40 break in miles only. It has every mod you could do to it, all the best parts, Turbo Pistons race cams, the list goes on and on. The head is a wok of art, again, with all the best stuff, ported, polished, plus 1 valves all the way around, guides on both intake and exhaust, ect ect.
Motor was designed and built for 20 pounds of boost, no expense spared.
Clutching, 2 complete sets. First, STM RAGE 6 primary and secondary and TEAM rapid response with Polaris secondary with turbo guts and helix.

Turbo is MCX high boost unit with wide band kit and AER Gauge. Billet intake. Inter cooler has fan mounted.
I spoke with Trey at MCX and he can tune the turbo and build a fuel map good for 20 pounds, big hp, or keep it at 11-12 pounds and map it for pump gas.
THAT STILL NEEDS TO BE DONE!!
Also have an aftermarket radiator for additional cooling, plus the stock one.
Car is in the reassemble stage, 85% finished, and I believe I have 95% of all parts needed plus spares.

What’s it worth? Let’s talk. P.M. Any ball park offers. If we are close, come take a look.
Again, just feeling the water, and will not part out.
I don’t know how to post pics but I can email or text if serious.
THANK YOU,
RICK

Feeling the water

Well guys, some things have changed in my personal and I may have to sell my custom 2012 RZR 900 4 seater. I am feeling the water to see what it may be worth to someone who appreciates what I started.

I WILL NOT PART IT OUT, SO PLEASE DONT ASK.

What I have, and this description will not do it justice.
2012 RZR 900 4 seater. Only 20 hours on car.
Full custom built DOM .120 wall cage with front bumper, roof mounted light bar, tied to rear with spare tire mount. Spare tire panel is on heims, raises on gas strut for bed access
All custom fab aluminum panels, sides are 3/4 high, front to back, rear is all aluminum with light box, side panels, rear panel, front end is all aluminum one of a kind custom.
Dash is all aluminum custom with turbo gage pod.
Aluminum roof, with aluminum boxed switch panel that runs along top of cage, inside. Hex Zues fasteners through out.
5 Hella lights in roof mounted light bar and 2 more in custom front bumper.
Custom cage is powder coated and all aluminum is raw, sand finish.
I designed this car to resemble an old school race car, I wanted to look different

The stereo consists of 5 channel JL audio amp, 500 wats of real power, JL audio
10W3 dual voice coil sub, 6" Boston Acustic Pro separates with crossovers.
Amp and crossovers are mounted under the dash in a custom built heavy duty
rack. Sub and speakers mounted in SSV Works enclosures. Car is wired for rear speakers as well.
Custom heavy duty battery box mounted under the rear seat with a Kinetik pro sound competition battery, and smart battery isolator. Battery weighs 65 pounds and will power the sound system for hours and hours.
Miles and miles of custom wiring harnesses, wrapped in conduit, and double warped in heavy duty electrical tape. Car is wired for accessories galore. Extra fuse box and relay bank wired in.
PRP Baja competition seats, extra wide, heated in the front, PRP bench in the
rear, all with embroidered logos in the head rests. 5 point harnesses front and rear. Very, very comfortable.
Sommers Brothers Racing 300M rear axles with 570 CV’S just serviced by S.B. Plus 2 stock spares.
Holtz Racing billet engine and transmission mounts.

Here is where it gets good.
The engine is a K&T 975 big block, built by KingR here on the forum, 40 break in miles only. It has every mod you could do to it, all the best parts, Turbo Pistons race cams, the list goes on and on. The head is a wok of art, again, with all the best stuff, ported, polished, plus 1 valves all the way around, guides on both intake and exhaust, ect ect.
Motor was designed and built for 20 pounds of boost, no expense spared.
Clutching, 2 complete sets. First, STM RAGE 6 primary and secondary and TEAM rapid response with Polaris secondary with turbo guts and helix.

Turbo is MCX high boost unit with wide band kit and AER Gauge. Billet intake. Inter cooler has fan mounted.
I spoke with Trey at MCX and he can tune the turbo and build a fuel map good for 20 pounds, big hp, or keep it at 11-12 pounds and map it for pump gas.
THAT STILL NEEDS TO BE DONE!!
Also have an aftermarket radiator for additional cooling, plus the stock one.
Car is in the reassemble stage, 85% finished, and I believe I have 95% of all parts needed plus spares.

What’s it worth? Let’s talk. P.M. Any ball park offers. If we are close, come take a look.
Again, just feeling the water, and will not part out.
I don’t know how to post pics but I can email or text if serious.
THANK YOU,
RICK

New USA made Heretic Light Bar! Forum Special

Hello guys and gals! Just wanted to show off our latest line of billet LED light bars. The body on these is made completely of 6061 billet aluminum by us on our own machines, lenses are cut of a diamond coated polycarbonate, all brackets and mounting hardware are made from a CNC laser cut steel, optics are a unique to Heretic PCB mated to some ultra efficient spot/flood reflectors. Optional colors on forged 7075 bezel bolts include blue, black, orange, silver, gold and red. The bars are joined in 10 inch sections so they are modular. By end of of the week we will have radius options on the 10-50 inch and orders will ship next week. Each 10 inch section weighs just 1lb!

These bars are what we believe can fill the gap between the Amazon bars and the overpriced bars. This is premium, handbuilt in the USA bar that we are selling at incredible prices.

For one week only we have the following forum member pricing: Price includes free 2 day shipping!

10 inch: $205 shipped
20 inch: $305.00 shipped
30 inch: $405.00 shipped
40 inch: $420.00 shipped
50 inch: $505.00 shipped

Comes with end mounts standard but not complete harness. Has pigtail coming off bar with Deutsch connector.

Below are pics…This is a standard Wraith with optional forged orange bezel bolts.




New USA made Heretic Light Bar! Forum Special

Hello guys and gals! Just wanted to show off our latest line of billet LED light bars. The body on these is made completely of 6061 billet aluminum by us on our own machines, lenses are cut of a diamond coated polycarbonate, all brackets and mounting hardware are made from a CNC laser cut steel, optics are a unique to Heretic PCB mated to some ultra efficient spot/flood reflectors. Optional colors on forged 7075 bezel bolts include blue, black, orange, silver, gold and red. The bars are joined in 10 inch sections so they are modular. By end of of the week we will have radius options on the 10-50 inch and orders will ship next week. Each 10 inch section weighs just 1lb!

These bars are what we believe can fill the gap between the Amazon bars and the overpriced bars. This is premium, handbuilt in the USA bar that we are selling at incredible prices.

For one week only we have the following forum member pricing: Price includes free 2 day shipping!

10 inch: $205 shipped
20 inch: $305.00 shipped
30 inch: $405.00 shipped
40 inch: $420.00 shipped
50 inch: $505.00 shipped

Comes with end mounts standard but not complete harness. Has pigtail coming off bar with Deutsch connector.

Below are pics…This is a standard Wraith with optional forged orange bezel bolts.




rock sliders

please someone help me out here.. i bought the Polaris rock sliders and they came with them shitty bolt things that go into the frame. First off they were b**** to get on and i had to take them off. Well the hardware is ruined and polaris won’t help me, any suggestions? lol

rock sliders

please someone help me out here.. i bought the Polaris rock sliders and they came with them shitty bolt things that go into the frame. First off they were b**** to get on and i had to take them off. Well the hardware is ruined and polaris won’t help me, any suggestions? lol