Just wanted to know if the stock valve clearance is gonna be ok? And torque specs for the primary and centrifugal clutches? Head bolts 19lbs? 9lbs rocker box cover bolts? And what about the torque specs on the two long 10mm I think bolts that run from the head to the jug with factory lock tight on them?
Hello everyone new to the site and new owner of a used grizzly. Im from north west north carolina.I purchased a 2011 grizzly 700 with power steering today with 1000 miles and 149 hours in pretty good shape for $3500 bucks. I hope I didn’t pay too much.
Hello everyone new to the site and new owner of a used grizzly. Im from north west north carolina.I purchased a 2011 grizzly 700 with power steering today with 1000 miles and 149 hours in pretty good shape for $3500 bucks. I hope I didn’t pay too much.
We have been advised that certain Polaris ATVs are causing injury and damage to consumers. We are currently investigating damage caused by extreme exhaust heat on Polaris ATV?s due to the location of the exhaust and extremely high exhaust temperatures. Our focus is on Polaris Sportsman?s built from 2012 ? 2016; however, if you own other models, we would like to hear from you.
If you own a 2012- 2016 Polaris Sportsman and have experienced extreme exhaust or engine heat making it uncomfortable/dangerous to ride your Polaris ATV, melting the seat/side cover of your Polaris ATV or causing injury to you, please contact us and tell us your experience. We are investigating these claims on behalf of consumers.
well after i discovered my rear swing arm was bent I decided to replace it and not try to fix it. $30 on ebay.
it is in the mail and will have it on friday. with that being said I also ordered a new set of swing arm bearings. Plan is to replace the bearings in the new swing arm for good measure.
I have the old swing arm and am tring to figure out how to get the old bearings out. I know i need to do it to the new arm so might as well try on the old arm first so if i screw it up it is not a big deal. I looked on youtube one guy welded the race and it "popped" out. not too sure of this method. I do have a wire welder if that is the only way. but there must be a better way of doing this? what tools do i need to to this job right? and what have you guys done to tackle this job.
hi everyone i have a 2005 polaris 800. my issue is the awd is not working here is what i know.
no voltage at front diff.
awd light on pod works.
jacked up rear end, put tranny in low, turned awd on and the front dont spin.
no codes in system.
front diff ohms out at 26.5 ohms
Went out for a group ride last weekend and partway through after a brief rest the bike wouldn’t start. Normal ride, no water or mud. Towed it back to the trailer and it did start but we shut it off and hasn’t started since. When i turn the key there is nothing, no sounds at all.
No error codes on the computer either. Did some tests with the volt meter and I have 12v at the battery and at the connections to the starter. All the other electrical works fine. Swapped out the relays to make sure that wasn’t the problem as well.
Could it be a bad starter? Is there a seperate solenoid on this machine? I’m stumped and looking for suggestions, i’m fairly handy but need some other ideas please.
Some say Renegade. Some say Arctic Cat. I saw Looney Tunes exhaust pegs that were perfect but cost $110! I want the outer end heel kick up pattern , so the Yamaha oversized ones are out. What’s the best way to go??
I’ve heard many a tale about the curved Renegade stock pegs ($45 on eBay), fitting right in nicely on any 07-15 Grizz footwell. Also hearing that cheaper ArcCat pegs do nicely as well and at less $! What would a Yami GNCC racer such as myself in the making, want to do to properly alleviate the terribly flat and useless stock pegs?? I’d care more for fit-ment issues being less if not nonexistent more so than I care about $29 or $49 either way. Well, with that said, let my maiden voyage here commence! (Talk amongst yasselves). Can’t wait to hear!
Hi all
New to me quad needs work, ball joints, front brakes work if u pumpem prob master or wheel cyl. Rear brakes ng, we will see when we open it up.
I could use some help. Mainly, please steer me to best place to buy parts.
Also I could use exploded views/parts diagrams, with table of part numbers. Anyone have for this yr model?
Thanks fellas
