Category Archives: Lighting, Stereo and Electrical

Protect mode with loud music

Running Duner Tunes system with 250w amp in Rzr 900xp. Also has winch. Installed system and winch when unit was brand new in 2012. It seemed to work fine thru 2013 and last summer (only used it very little last year due to work schedule) the amp would cut out if music turned up loud. Checked code and red lite on amp flashing and trouoble shooting says low amps so goes to protect mode. Battery is fully charged. Would upgrading to new or bigger battery help?(battery in rzr is the original).

Protect mode with loud music

Running Duner Tunes system with 250w amp in Rzr 900xp. Also has winch. Installed system and winch when unit was brand new in 2012. It seemed to work fine thru 2013 and last summer (only used it very little last year due to work schedule) the amp would cut out if music turned up loud. Checked code and red lite on amp flashing and trouoble shooting says low amps so goes to protect mode. Battery is fully charged. Would upgrading to new or bigger battery help?(battery in rzr is the original).

Dimly lit switches from ACC jack

I need some help from someone smarter than me. First let me say thank you for all the great threads and information about wiring and different installs on this forum. There are some guys that really know their stuff and offer some great info.

I have searched and read almost every thread in this section and cannot find the answer I’m looking for.

With that said, I have installed 4 Contura switches from OTRATTW (5 pin) in my XP1k and have wired a dome light, a lighted whip, light bar, and a blank for future stereo use.
I ran a 6ga wire with 30amp in line fuse to a Blue Seas Fuse Block under the hood. I have everything wired from the fuse block out to respective places.
I have everything grounded to a junction box and then to the frame. I did this because I want to be able to turn anything on without having to turn the key on and log hours on my meter. That all works great.

Now the problem, I wired power from the factory ACC terminal under the hood for the bottom lights on my switches. These are 4 1amp (or so) led lights that illuminate the bottom of the switch to indicate "light bar" "dome light" etc. I wanted those to come on with the dash lights. When you turn the key off, they stay brightly illuminated for about 20 seconds as does the tail lights and other dash lights. When everything clicks off, my 4 switches stay dimly lit. Like a little bit of juice is bleeding to them.

I disconnected the main power and tried it thinking power was bleeding through the switches. That wasn’t it.

If you pull the ACC 20amp fuse in the factory fuse box under the seat, they go off completely. If you pull the EFI relay, they go off completely. if you switch the relay with another one, same thing, they stay lit.

Has anyone else experience this?
Thanks for any help anyone has to offer.

3 inch dually cubes on sale!! this week $59pr shipped

got 60 pair of these. normally they are $99 a pair, but were running a special on them.
ON SALE THIS WEEK!!!!

$59.99 a pair shipped!!!!!

16 watt, 1400 lumen each light. cree emitters, 2 year warranty. great for extra light on the bumper, or A pillars. also work awesome for backup lights.

sold as a pair, $69 a pair shipped to your door.

link to buy VVVV
3inch cubes 16watt sold in pairs

Jeremy
wvoffroadgear

Tapping out…mounting 30″ Totron radius under visor

Ok so I’ve used the search tool and have read as many posts as I can on the subject and although I’ve found some tips that got me close, I’m still without a solution! I need your help guys and gals.

I have a Totron 30" radius double row light bar and want to mount it underneath the OEM sunvisor and can’t for the life of me figure out which mounts will work. I’ve looked at the Axia Alloys page but nothing jumps out at me as the silver bullet on which mounts to use.

I WANT to use brackets that attach to the cage uprights and not the horizontal bar between A-pillars for fear that I’ll have to cut/trim the visor. If this isn’t possible, I’ll do the latter.

Can anyone tell me what to use???? Thanks in advance!

Tapping out…mounting 30″ Totron radius under visor

Ok so I’ve used the search tool and have read as many posts as I can on the subject and although I’ve found some tips that got me close, I’m still without a solution! I need your help guys and gals.

I have a Totron 30" radius double row light bar and want to mount it underneath the OEM sunvisor and can’t for the life of me figure out which mounts will work. I’ve looked at the Axia Alloys page but nothing jumps out at me as the silver bullet on which mounts to use.

I WANT to use brackets that attach to the cage uprights and not the horizontal bar between A-pillars for fear that I’ll have to cut/trim the visor. If this isn’t possible, I’ll do the latter.

Can anyone tell me what to use???? Thanks in advance!