Category Archives: Honda Rancher

honda rancher 420 inline fuel filter

Why in God’s name would they put the fuel filter in the pump? Mine is clogged up. Honda here dosnt even stock the filter For my bike. Can I put an inline filter from the tank to the pump canister ? Gravity will still put enough fuel in the canister as fast as the pump can take it…right?

2003 Rancher 350 FE Front Wheel Bearings

Found out one side of my Rancher front end has bad bearings. Was getting ready to order a set for both sides, and need a little information. The original parts diagram shows 2 bearings and a spacer. The aftermarket bearing shows only one per side.

I saw on the forum which aftermarket bearings were recommended, so I am looking at these

Pivot Works, Inc.

Front Wheel Bearing and Seals Kit Honda TRX350FE 2000-2006

Does the one bearing take the place of the original 2 bearings and spacer.
I don’t mind buy the OEM bearings if they are better.

lost power and ticking! please help!

I have a 2014 Honda Rancher trx420FA with a snorkel. Big Bore kit. Big Gun Exhaust. Power Commander 5.

I have a loud ticking noise and every time I go over 50% throttle. The wheeler bogs down. Rod isn’t bent and the push rods look good. I have no what it could be. I missing out on great riding weather. Any ideas? I want to have this fixed this week! Please help!

More power

I have a 2014 honda 420 sra so new body style I’m curious on what would give me a little more horsepower the most cost efficient way would drillin the baffle out give me more power ? Or just noise and if I did would it mess with the efi?
Also what are the best/most cost efficient exhaust and efi opti set up thanks guys

honda 350 es part?

My honda 350 rancher es has been having intermittant shifting problems for the past 2 years after getting pretty deep in water. It will just flash for a few months and then shift fine…then the process starts over. Finally getting it taken apart to figure out what it is. If I follow the cable coming out of the let handle bar it goes to the front underneath just behind my winch.

There are 4 wiring connectors down there under the "hood". From the right side (if you were sitting in the seat) the 1st one is round, the second one is the one that I thought came from the left handle bar but alas…it comes from the actual display. I got it apart and the part coming from the led display area had corrosion in it pretty bad. I tried to scrape it off carefully but wound up breaking one of the pins off. So now I know it needs to be replaced. I have it taken off, the other end has 2 plugs that go into the computerized card in the display case…..what part is this? I need to get one ordered and can’t figure it out from the service manual.

Second question is could the corrosion on this part be what my problem was? And do I need to replace both ends. The other side (female end) looks pretty clean.

Thanks if anybody can tell me which part to order.

Keith

honda 350 es part?

My honda 350 rancher es has been having intermittant shifting problems for the past 2 years after getting pretty deep in water. It will just flash for a few months and then shift fine…then the process starts over. Finally getting it taken apart to figure out what it is. If I follow the cable coming out of the let handle bar it goes to the front underneath just behind my winch.

There are 4 wiring connectors down there under the "hood". From the right side (if you were sitting in the seat) the 1st one is round, the second one is the one that I thought came from the left handle bar but alas…it comes from the actual display. I got it apart and the part coming from the led display area had corrosion in it pretty bad. I tried to scrape it off carefully but wound up breaking one of the pins off. So now I know it needs to be replaced. I have it taken off, the other end has 2 plugs that go into the computerized card in the display case…..what part is this? I need to get one ordered and can’t figure it out from the service manual.

Second question is could the corrosion on this part be what my problem was? And do I need to replace both ends. The other side (female end) looks pretty clean.

Thanks if anybody can tell me which part to order.

Keith

2015 Rancher IRS wheels

I recently bought a 2015 Honda Rancher 420 w/IRS. I put some old SS112 rims/ 26" mudlites on it but the back tires stick out of the finders. I want to buy some new rims and tires that will fit in the back finder walls. Do I need to buy specific IRS rims or what? I want MSA M20 wheels w/ 27" Mega MayHems for it. Will that fit right or not? I honestly don’t know much about ATV tires & I need help!

Es350

new to forum just ran our Rancher first time since sitting through winterhad it warming up while I raked leafs it died while idling it was low on gas so I added the last gallon I had from the snowblower gas good gas and tried to start idled for a couple seconds wouldn’t take any throttle and died again and back fired tried to restart and it wouldn’t start and when I stopped cranking it over it backfired again letting it rest now and will check plug tomorrow

I’m back in the atv game!!!!

Well guys this Sunday I’m going up to Atoka, Oklahoma to meet a guy to buy my rancher! It is a 2013 rancher 420 4×4 at irs. It has power steering also! It only has 53 hours on it, the guy bought a project car and needs cash so he is getting rid of this atv. I’m paying 3600 bucks for it. Everything is mechanically sound, there isn’t been any staining on the engine! Here is a picture.

Attached Thumbnails

Click image for larger version

Name:	image.jpg
Views:	N/A
Size:	30.2 KB
ID:	24016