Went out for a ride today for the first time in a while and I get the check engine light and the hi temp message. My fan isn’t coming on either. It has never overheated before. I’ve read somewhere that you can bleed the air off the heads would this help in my case? Any advice is greatly appreciated.
I just ordered a qsc primary clutch for my renny 1000 I am assuming it comes with everything I need 2 bolt on the question I have is my secondary do I go and get the stm or keep the stock and do I keep the red epi spring in there or do I go back to stock since I am running 30s on it now any help would be much appreciated.
My renegade seems to be a little boggy with my two brothers exhaust on compared to stock, I emailed two brothers and they told me a tuner wasn’t needed, my shiftout is only about 7000 with the two brothers exhuast on… Should I get a tuner?
Hi guys,
I bought a lot of mixed parts and this u-joint was in it. I thought it was part number 705400391 for an 2006-2011 Renegade 500, 650, and 800 but I think I’m wrong on this. There is a spicer number of 2105056 stamped into it. This has 18 splines, and measures approximately 3" long and 2-1/4" wide. Any help would be appreciated!
When I thought I was good to go after going over everything, trying to over haul my bike.. I snapped the rear driveshaft..
I know the 500 and 800 run pretty much the same parts..
So will a 2013 rene rear drive shaft fit in my 07 800?
I ask because I thought in 09 they changed something.. I can get the whole prop setup for $170.. Which is half the price.. If not what model/year setup should I get for a better/stronger setupz
I also found out I can get a 2013 or 14 xmr 650 rear diff and drive shaft for $550.. Will that work/fit also?
When I thought I was good to go after going over everything, trying to over haul my bike.. I snapped the rear driveshaft..
I know the 500 and 800 run pretty much the same parts..
So will a 2013 rene rear drive shaft fit in my 07 800?
I ask because I thought in 09 they changed something.. I can get the whole prop setup for $170.. Which is half the price.. If not what model/year setup should I get for a better/stronger setupz
I also found out I can get a 2013 or 14 xmr 650 rear diff and drive shaft for $550.. Will that work/fit also?
okay guys, I’m stumped. i have a 2014 renegade 1000 xxc. i put the factory wench on it, everything worked great for about 4 months.. when i decided to put heated hand grips on and the grips got left on for about 2 weeks and then i had a dead battery, so i charged it and rode around on a ride and it died again. ordered a new battery put a nice charge on it UNHOOKED the heated hand grips and then took it out for a ride on a brand new battery. did the same thing about half way through the ride i shut my four wheeler off and it did not want to start (low Batt) I’m completely stumped.. any suggestions? thanks!
So I removed the primary to service the one-way bearing & reinstalled. I’ve read on here spec is 74lbf-in & also 89lbf-in +/- 6lbf-in however the service manual I have states 100N-m or 74lbf-ft (note=ft). This is a big variance. I torqued to 74lbf-in & didn’t have to even hold it to reach spec. I think 74lbf-ft is too tight. So what is the correct spec?
So I removed the primary to service the one-way bearing & reinstalled. I’ve read on here spec is 74lbf-in & also 89lbf-in +/- 6lbf-in however the service manual I have states 100N-m or 74lbf-ft (note=ft). This is a big variance. I torqued to 74lbf-in & didn’t have to even hold it to reach spec. I think 74lbf-ft is too tight. So what is the correct spec?
Need help with 07 800 renegade I broke the through shaft and can’t find out a way to take out, went to different shops in city and all gave different answers just want me to pay them 5 hrs to do