All posts by dstech

new ATV bad battery

I just bought a 2017 sportsman 850SP in late November, I started and used it two times shortly after, only 3 miles on it. the problem, I went to start it two weeks ago, and the battery was dead. I put a charger on it for a hour, and it started up, let it run for 10 minutes. today I went to start it, and again it was dead. put a cheap tester on the battery, and it said 20 percent.

what is the problem here, do I bring it back.

Quadboss Pile Driver Plow System FAIL

Well here’s my month old Quadboss Pile Driver 60" snow plow after a few uses. The plow is actually in the straight position. If you look you will see the silver pivot bolt is no longer located in the center of the push tube. The bolt is not broke. I was able to finish plowing with it and was able to adjust it to different positions just fine. Pretty disappointed in this plow overall.

First use with it I made it half way down the driveway before both of the mounts for the plow feet bent right over. I removed those and ended up putting a piece of pipe over the cutting edge which actually worked better overall. And now this. Bummer.

#Quadboss

Attached Thumbnails

Click image for larger version

Name:	20161230_184953050_iOS.jpg
Views:	N/A
Size:	1.75 MB
ID:	66546
 

Click image for larger version

Name:	20161230_185007946_iOS.jpg
Views:	N/A
Size:	2.30 MB
ID:	66554
 

Click image for larger version

Name:	20161230_185051327_iOS.jpg
Views:	N/A
Size:	2.67 MB
ID:	66562
 

Quadboss Pile Driver Plow System FAIL

Well here’s my month old Quadboss Pile Driver 60" snow plow after a few uses. The plow is actually in the straight position. If you look you will see the silver pivot bolt is no longer located in the center of the push tube. The bolt is not broke. I was able to finish plowing with it and was able to adjust it to different positions just fine. Pretty disappointed in this plow overall.

First use with it I made it half way down the driveway before both of the mounts for the plow feet bent right over. I removed those and ended up putting a piece of pipe over the cutting edge which actually worked better overall. And now this. Bummer.

#Quadboss

Attached Thumbnails

Click image for larger version

Name:	20161230_184953050_iOS.jpg
Views:	N/A
Size:	1.75 MB
ID:	66546
 

Click image for larger version

Name:	20161230_185007946_iOS.jpg
Views:	N/A
Size:	2.30 MB
ID:	66554
 

Click image for larger version

Name:	20161230_185051327_iOS.jpg
Views:	N/A
Size:	2.67 MB
ID:	66562
 

2013 500fpm surging at idle

Started surging at idle but could turn it off and back on and would quit.Well luck ran out and now surgess always at idle.Pulled injecter outand cranked it over and sprayed as should.Checked coil ground etc. and foundnothing.Runs a-1 other than idle surge.Any help anyone?Thanks

2013 fpm 500 surging at idle

Started surging at idle but could turn it off and back on and would quit.Well luck ran out and now surgess always at idle.Pulled injecter outand cranked it over and sprayed as should.Checked coil ground etc. and foundnothing.Runs a-1 other than idle surge.Any help anyone?Thanks

Swapping computers around.

Got the two inch lift kits put on added a fire extinguisher to both bikes was looking at the computer and something hit me. :eclipsee:

I have a 450 and a 570. Both 2016 Couldn’t I take the computer off the 570 stick it on the 450, send that one that was on the 450 in to RVS and have it maxed out to go back on the 570. ?
There the same motors correct.??

Rut Ro,, minds in gear now, what you guys thinK?