Category Archives: Grizzly Accessories

Wench Mount ?

I think I will go with the Superwench terra wench for my atv. One review said the Superwench mount put the rollers in a down angle and made the cable off center . He changed to a different mount to solve the problem. Any of you guys have this problem with their mount or maybe he did something wrong ? Would the mount Yamaha sells work better for the Superwench wench ? I hate to ask a lot of stupid questions here but I know nothing about this stuff. Thanks

ATV Guru Brush Guard

Been kicking around getting a brush guard for a while. I almost pulled the trigger on the warn brush guard but held off.

I can’t find very many pictures or posts of people that have the atv guru brush guard, just wondering what people thought about them good or bad.

Thanks!

What Brand of Windshield is this?

I bought this 09 Grizzly used just recently and although I was able to clean up the windshield so we can sort of see through it, I would like to find a replacement windshield for it. I can shine up the fairing, but if anyone knows what it would be I would sure appreciate it. Thinking it was a yamaha, but the dealer doesn’t show anything like it now anyway. Here are the pics:

Thanks, Ken

Attached Thumbnails

Click image for larger version

Name:	image1.JPG
Views:	N/A
Size:	870.5 KB
ID:	22202
 

Click image for larger version

Name:	image2.JPG
Views:	N/A
Size:	298.5 KB
ID:	22210
 

Click image for larger version

Name:	image3.JPG
Views:	N/A
Size:	480.4 KB
ID:	22218
 

Cycle country plow 2016 grizzly..

All,

My dealer just installed my cycle country mid mount plow on my 2016 grizzly SE, and I had a question regarding the ground clearance. From what I see underneath, leaving that mount on while not plowing, but rather off roading and such it looks pretty stout to me, except the two eye hooks welded on for attaching plow. Am I an any danger leaving this on while off roading? Do any of you think that those welded mount hooks could be damaged by say a rock or something else? Whatabout getting hung up on things? I am new to these machines and setups, so I apologize in advance if I am asking stupid questions. I never knew I had three different mount options, I just went with what my dealer recommended as their best seller. Thank you all in advance.

660 plow setup questions……

Ok I’ve got a homemade push tube plow setup on my bike. Seems to me that the blade is too close to the bike. I Need someone to post common measurements front bumper to plow face or something common like inches between blade n tire at angled position……..
My options are to cut n sleeve the push tubes to extend them out. ORRRRR cut the mounting plate tabs that hang down and reweld them X amount of inches forward. This woukd be the more difficult of the 2 due to the plow plate narrowing towards the front.
Also as the pic shows I’m not getting the amount of lift I’d like to see. (9.5" ground to cutting edge) I know moving the plow forward will naturally give me more lift but I’m looking for more. I think my tubes should have a slight bend at the red arrows to create more lift.
Opinions??
How many degrees would work? ( I straightened the tubes because the welds broke free and they were bent wayyyy over.)

Attached Thumbnails

Click image for larger version

Name:	20151207_182430.jpg
Views:	N/A
Size:	3.09 MB
ID:	21937
 

Click image for larger version

Name:	2015-12-07 18.40.36.jpg
Views:	N/A
Size:	3.32 MB
ID:	21945
 

Click image for larger version

Name:	2015-12-07 18.41.29.jpg
Views:	N/A
Size:	3.25 MB
ID:	21953
 

handle bar with risers

hi guys looking for ideas on handle bars with riser,
I had the combo kit from rox on my old grizz but they have been out of stock for awhile and they cant seem to answer when they will have them again.
I can buy the 5 inch riser from them but need bars cant really get a read on bars though , pro taper has a cr high bend and so does other brands but not sure if they are same as fly cr high which comes in combo kit .
so what are other people using ?