Hello, new to this site & considering purchasing a 2008 ATP 500 with 235 hrs., 1600 miles . Used but not abused , cosmetic damage. Wants 3200.00, seems high ? Any thoughts ? Thx. in advance .
08 Honda rancher 420 bent the out drive
Hello everyone I recently broke my ujoint causing the out drive to bend enough to cause the rear seal on the back of the block to leak, I’m trying to figure out which part I have to replace is that the final drive or the out drive shaft ? In the picture which part do I need to replace 1 or 2 
the part that is bent on my bike is the rear shaft coming out of the block to the rear diff.
the part that is bent on my bike is the rear shaft coming out of the block to the rear diff.
Sent from my iPhone using Tapatalk
2016 570 tires?
Does anyone know if 27x9x14 and 27x11x14 ripsaws mounted on 14 inch wheels with a 4+3 offset will fit the 570 without any rubbing? Would it be better to just go with 26 inch tires to be safe
New from Colorado Mtns
My wife and I (I’m 74, she’ll be 73 next month) have just purchased 2 used ATV’s and riding them makes us feel like kids again. We are the proud owner’s of a 2004 yellow and a 2005 Mossy Oak (now purple) Sportsman 500 HO’s, both low mileage/hours. We went on a 29 mile trail ride Saturday and her’s ran Great. Mine did likewise most of the time. Pulling hills it would bog down like the choke was on. Had one very sharp rifle like backfire going down that same hill and it stumbled for a couple of minutes and then seemed to clear itself out and ran fine on the level ground. I pulled the plug (sure glad mine still had the tool kit with that special plug combo) after church yesterday and it is the correct NGK plug but it was really black and slightly damp. Cleaned it and checked the gap, which was correct. Re-installed fired it up and raced my wife around the pasture a few laps and it seemed to be ok. If this were the ’60’s and this was my ’56 ford 312 convertible I’d say the carb is jetted wrong (we live at 8500′ and were riding at approx 9500′. That carb looks likes it’s hard to get out. I’m not a mechanic. I’m still teaching high school- I guess that’s why this is so wordy. Any advice and/or tips?
Front grind in 4×4 sometimes, any idea?
I’ve searched for this but couldn’t find what I was experiencing.
On my last ride while going through a gravel pit I climbed a steep hill in 4×4 low with loose dirt/gravel and at the top I needed to turn hard left which after a grinding noise started coming from the front. I immediately stopped, switched to 2wd and back into 4wd and it went away. It did this twice.
Any explanation for this? Cause for concern? Normal Can-am weirdness?
Thank you muchly in advance for any info.
2016 Outty MAX XT, 850 with 1600kms (60hrs)
Best Canadian QSC DEALER?
Hi, looking at buying a QSC REV X clutch for my 16 renegade XMR, right now I have Monster Tune Injection ECM, Auto tune, NPP full Single Cone exhaust, and rev limiter raise to 8850, looking to use the extra range with cams, and a QSC clutch, anyone knows a good dealer aside then FFUN not a fan of there service barely ever answers phone or Email
Best Canadian QSC DEALER
Hi, looking at buying a QSC REV X clutch for my 16 renegade XMR, right now I have Monster Tune Injection ECM, Auto tune, NPP full Single Cone exhaust, and rev limiter raise to 8850, looking to use the extra range with cams, and a QSC clutch, anyone knows a good dealer aside then FFUN not a fan of there service barely ever answers phone or Email
Parts that I am going to by for recon
I have came down to purchasing a coil, starter,wire harness,and a stator for 112.50 is this a good buy
Renegade Winch Mount R&D….get a free winch!
Hi Can-Am Gang,
We are looking for a 2014-2017 Renegade to get into our facility at Motoalliance so we can build a winch mount for this. We can include one of our 3000lb VIPER winches for free if you are willing to bring your machine into Rogers, MN for 2-3 weeks. We can also include 50% off any other accessories we sell, like snow plows, lights, and implements.
We are looking for a 2014-2017 Renegade to get into our facility at Motoalliance so we can build a winch mount for this. We can include one of our 3000lb VIPER winches for free if you are willing to bring your machine into Rogers, MN for 2-3 weeks. We can also include 50% off any other accessories we sell, like snow plows, lights, and implements.
Please shoot me a PM if interested, or send a direct email to me at peter@motoalliance.com. Thanks!
Renegade Winch Mount R&D….get a free winch!
Hi Can-Am Gang,
We are looking for a 2014-2017 Renegade to get into our facility at Motoalliance so we can build a winch mount for this. We can include one of our 3000lb VIPER winches for free if you are willing to bring your machine into Rogers, MN for 2-3 weeks. We can also include 50% off any other accessories we sell, like snow plows, lights, and implements.
We are looking for a 2014-2017 Renegade to get into our facility at Motoalliance so we can build a winch mount for this. We can include one of our 3000lb VIPER winches for free if you are willing to bring your machine into Rogers, MN for 2-3 weeks. We can also include 50% off any other accessories we sell, like snow plows, lights, and implements.
Please shoot me a PM if interested, or send a direct email to me at peter@motoalliance.com. Thanks!
